Extending the Washing Machine Platform on the Balcony — Day 1
That's right: when I replaced the boiler, I had no choice but to extend the washing machine platform if I wanted to stack them, so that's what I did. I could ha
GGAMI·
That's right: when I replaced the boiler, I had no choice but to extend the washing machine platform if I wanted to stack them, so that's what I did.
I could have called someone in, but why? I still wonder why on earth I started this whole thing.
To give you the total upfront, it cost about 110,000 won.
Supplies I bought
5 kg of cement
25 tiles (?)
3 kg of Dryfix
1 kg of white cement grout
Trowel
Paint bucket
Mixing drill bit
Tile cutter
And so on and so on...
★시멘탈 몰탈 작업
[준비물]
- 흙삽
- 유리닦이
- 시멘트
- 혼합 통
- 합판 거푸집
- 수평자
- 글루건
1.안에 모두 정리 및 청소하기
2.합판 글루건으로 고정시키기
3.시멘트 몰탈 물과 섞어서 제조하기
4.시멘트 몰탈로 만들기
5.시공일로부터 2일 후까지 양생
6.청소하기 및 공구 정리하기
합판 크기만큼 제작
(양생 4일)
★드라이픽스 + 타일 붙이기
[준비물]
- 흙삽
- 타일
- 수평자
- 타일 재단기
- 드라이픽스
- 혼합 통
1.크기에 맞게 타일 재단하기
2.드라이픽스 제조하기
3.드라이픽스 바르고 타일 붙이기 (수평 !!!)
(양생 3일)
★백시멘트 줄눈 만들기
[준비물]
- 실리콘 그거 넣는거
- 백시멘트
- 혼합 통
- 스펀지
1.줄눈 제조하기
2.줄눈 바르기
3.스펀지로 잘 닦기
★공구 정리
- 모든 공구는 복층에 두고서, 잘 안쓰는건 안에 넣고, 자주 쓰이는건 밖에 꺼내둔다.
>> 건축물 마대자루 하나 사서, 그 안에다 모두 다 갖다 버린다.
★다음날
[준비물]
- 스펀지
1.스펀지로 백시멘트 한번 더 닦기
106,480원
This is what I wrote in the txt file.
Anyway... I got started.
I needed formwork, so I had some wood cut and bought it, but I was supposed to get 4 cm and ended up getting 40 cm. I've never seen such a fool... haha.
So I reordered it, but
maybe because the wood was too thin, it arrived warped.
So... I screwed two pieces together to keep them from bending as much as possible. (Luckily, I ordered three since they were cheap.)
First, I cleaned the existing tiles as much as I could, then secured the formwork.
I put tiles behind it because I saw someone do that somewhere and copied them.
I mixed it well to keep the dust down.
But the bottom wasn't done very well. I kept working on it with the trowel.
But then I ran into a problem.
I calculated carefully and used 5 kg, but as I worked, I realized I was running short.
The floor tiles were 200*200, so I had originally planned to extend it by 10 cm...
I ended up being way, way short!!! So I kept pushing the formwork back and back... and settled on 6 cm...
(If I move the tile forward, it can go up to 7 cm, so it would end up being extended by 7 cm in total.)
And here was another mistake...
Since the floor slopes, there was a tiny gap in the middle even with the formwork in place.
In other words, if I used that formwork to level it, both sides would end up lower and the center higher.
But I just went ahead with the job.
So, after a day had passed... I removed the formwork.
Some bits had come out through the gap in the middle, so I tidied and cleaned everything up.
Then... over the next three days... while it dried... I also brushed on water for curing (?).
